Page Top Enquiry Email Contact

SLM 3D Printer

SLM printing uses selective laser melting technology which melts metal powders and solidifies layer by layer until a three-dimensional part is built. During the process, the ruler in the build chamber will pave one layer of the metal powder, a high powered laser selectively fuses the powder by tracing cross-section of the part on the surface of a powder bed and then a new coat of material is applied for the next layer. The whole process is in a high vacuum chamber or full of protective gas chamber to avoid the metal powder reacts with oxygen at high temperature.

ZRapid is using a high energy and fine spot laser, The equipment can complete complex parts in a very short period time while using conventional methods that will take several weeks or even months to complete in comparison. Parts not only have precise dimension, high tensile and high density, but also excellent in mechanical properties. Mainly used for rapid production of high-precision, high quality metal parts.

  • Fiber laser
  • Fast galvanometer
  • iSLM Control System
Materials: Stainless Steel( 316L ) Aluminium Alloy( AlSi₁₀Mg ) Titanium Alloy( TC4 ) Co-Cr Alloy( MP1 ) Die Steel( MS1 ) Cuprum( Cu )

Online consulting

KEY FEATURES

High speed · High precision · High quality

ZRapid SLM 3D Printers
  • Parts with high quality surface before polishing
  • Parts in high accuracy, for precision samples
  • Directly produce functional metal parts, simplify the manufacture process
  • Parts have metallurgy and mechanical properties, relative density higher than 99%. Post process is unnecessary
  • Parts can be printed within minutes to hours according to the size and complexity
  • Parts can be finished in minutes or hours based on the complexity
  • Directly produce functional complex geometric parts like snap-fit or loose joint hinge
  • Widely chosen materials, the metal powder could be single metal or alloy
  • Especially for single part or small amount of functional parts

Product Specifications

  • iSLM150 Specifications

    LASER SYSTEM

    TypeFiber laser

    Wavelength1064nm

    Power200W / 500W

    RECOATING SYSTEM

    Processscraper paving

    Normal Build0.05mm

    Quick Build0.05~0.10mm

    Precision Build0.02~0.05mm

    OPTICAL & SCANNING

    Beam (diameter@1/e2)0.04~0.15mm

    Scanning GalvanometerHigh Speed Scanning Galvanometer

    Parts Scanning Speed1.0~2.0m/s (recommended)

    Blank Jumping Speed10.0m/s (recommended)

    Reference Building Speed2~15cm³/h

    SHIELD SYSTEM

    Protective gasN2 / Ar

    Flow Control0~3 L/min intellient adjustment

    dust extraction controlHigh efficiency Protection recycling system

    BUILD VAT

    VolumeApprox. 4.5L

    Size150mm(X) × 150mm(Y) × 200mm(Z)

    Max Weight20kg

    TypePrecision resistor heater

    MaterialsStainless Steel / Die Steel / Titanium Alloy / Aluminium Alloy / Co-Cr Alloy / Nickel Alloy / Cuprum etc.

    SOFTWARE

    NetworkEthernet, TCP/IP, IEEE802.3

    Control SoftwareiSLM(Presto SLM)

    Date Preparation Software3dMagic

    Data InterfaceCLI file, SLC file, STL file

    INSTALLATION CONDITION

    Power200~240VAC 50/60Hz, single phase, 15Amps

    Ambient Temperature20-26ºC

    Relative HumidityLess than 40%, non-condesing

    Size1.55m(W)×1.10m(D)×1.90m(H)(Operating computer is not included)

    WeightApprox. 1000kg

    WARRANTY

    Laser5000 hours or 12 months (whichever comes first)

    Main Machine24 months from installation date